Полезное:
Как сделать разговор полезным и приятным
Как сделать объемную звезду своими руками
Как сделать то, что делать не хочется?
Как сделать погремушку
Как сделать так чтобы женщины сами знакомились с вами
Как сделать идею коммерческой
Как сделать хорошую растяжку ног?
Как сделать наш разум здоровым?
Как сделать, чтобы люди обманывали меньше
Вопрос 4. Как сделать так, чтобы вас уважали и ценили?
Как сделать лучше себе и другим людям
Как сделать свидание интересным?
Категории:
АрхитектураАстрономияБиологияГеографияГеологияИнформатикаИскусствоИсторияКулинарияКультураМаркетингМатематикаМедицинаМенеджментОхрана трудаПравоПроизводствоПсихологияРелигияСоциологияСпортТехникаФизикаФилософияХимияЭкологияЭкономикаЭлектроника
Measuring tools
|
|
When accurate measurement of the part is required, the vernier calipers, micrometers and slide gauges are used. When it is not so important to have an accurate measurement of the part, metal rules, inside calipers and outside calipers will do.
Steel rules server for determining the length and sometimes the depth of the part to be measured. Steel rules are graduated in millimeters, but in the USA and England they are graduated in thirty-seconds and sixty-fourths of an inch.
The outside calipers are used for determining the internal diameters of the part. Its construction is almost similar to that of the outside caliper measurements of the part. The outside and inside caliper measurements may be read by placing the legs of the calipers on a rule and placing one leg and the end of the rule against a flat surface.
Vernier calipers can be used for measuring both external sizes of a part. By using vernier calipers measurements up to 001 may be determined. Vernier calipers consist of a primary steel scale and four jaws. Jaws are integral with the scale. Jawsattached to the frame sliding along the scale. The frame may be clamped on the scale in any position by means of an adjusting screw. External surfaces may be measured with jaws, while internal surfaces are measured with jaws. Тhe depth of recesses is measured with a depth rod. A vernier on the frame serves for measuring fractional parts of a millimeter.
The micrometer is an instrument for precise measurement of length and thickness of a part to one ten thousandth of an inch. The principle of operation is similar to that of vernire calipers. A graduated thimble serves as the primary scale. The scale on the barrel of the micrometer is used for the vernier reading. The part to be measured is placed between the anvil and micrometer screw, which is called a “movable spindle”. By rotating the thimble, the spindle is removed or approached to the anvil. By rotating the ratchet thimble the spindle is moved and thus the partis pressed to the anvil. Thereupon the rotation of the ratchet thimble is discontinued, the micrometer opening is fixed by the lock nut and the reading is taken. The micrometer reading is the sum total of the barrel divisions, the thimble divisions with respect to the axial line on the barrel, and the vernier reading.
The dial indicator is a gauge with a graduated dial and an indicator pointer connected to a test point by a system of levers. Any movement of the test point is magnified by the indicator pointer. The dial indicator is used to check the shape of a part, the precision of its machining, as well as for checking the accuracy of cuttingmachines.
Thread plug gauges or internal gauges, being of “go” and “no-go” type, are generally used for testing threads or tapped holes.
Depth gauges are used for measuring the depth of grooves and holes. Their principle of operation is similar to that of vernier calipers. A primary scale sliding in a frame may be locked in any position by a screw. The depth of a groove or a hole is measured by means of the primary scale and a vernier. Conical surfaces are measured with control gauges.
The universal angle gauge consists of a base with a primary scale attached to the base. A quadrant with a vernier may be moved along the arc of the base. A triangle may be attached to the quadrant by means of a holder. In its turn a detachable rule is attached to the triangle. The triangle and the detachable rule can be moved along the face of the quadrant. Angles can be measured within the range of 0 to 320 by means of the universal angle gauge.
1. Прочтите текст и выполните следующие за ним упражнения.
2. Используйте следующие слова и выражения в собственных предложениях:
Drawing, to measure, to involve, mating part, accuracy, slide gauges, vernier calipers, depth gauges, clearance gauges, micrometer, inside calipers, to graduate, internal diameters, to slide, adjusting screws, lock nut, tapped hole.
3. Переведите следующие группы слов, обращая внимание на суффиксы:
To measure, measuring, measurable, measured, measurement; to compare, comparative, compared, comparison; to signify, significant, significance; to depend, depending, dependence, dependent; to graduate, graduated, graduation; accuracy, accurate; precise, precision; general, generally, generation.
4. Подберите синонимы:
To place, inside, outside, to be similar, according to, with reference to.
5. Заполните пропуски предлогами in accordance with, by means of, within for, to, of:
1. Machine parts should be manufactured … their respective drawing. 2. … a micrometer it is possible to make measurements to a very high degree of accuracy. 3. Calipers are used for measurements to … 0.18 mm. 4. Measuring tools should be chosen … the machine part to be measured. 5. He micrometer is an instrument … measuring directly … thousandths, and estimating to quarter thousandths … an inch, … its range.
6. Переведите следующие предложения, обращая внимание на значение выделенных слов:
1.The principle involved in the operation of the micrometer is explained in technical text-books. 2. The instruction on the use of this dial indicator is rather involved. 3. These drawings and their explanations are given to illustrate the principles involved. 4. Different kinds of instruments are used tomeasure holes of considerable depth. 5. A millimetre is a measure of length. 6. Steel plates usually vary be sixteenths of an inch. 7. By dividing the load required to break the specimen by its area, the ultimate tensile strength of material is obtained. 8. By accuracy of from is meant not only the exact duplication of irregular profiles, but also the accuracy of from embodied in squares, true cylinders, cones, etc.
7. (a) Переведите текст с помощью словаря:
A range of optical instruments for measuring surface finish, which are relatively inexpensive and of very robust design, and afford the advantage that they can readily be applied under both workshop and inspection-room conditions, is being produced by many plants. Known as optical devices, these units are of modern designs. The portable device is intended for checking the relatively coarse finishes produced by planing, turning, and milling.With this device a beam of light is directed past a straight, opaque edge, and through a lens at an angle of 45 to the work surface, and the line of intersection is observed at an angle of 90 to the light beam, through the eyepiece of the microscope.
(b) Задайте три вопроса к тексту и ответьте на них.
8. Используя данные слова и выражения, объясните принцип работы нижней измерительной шкалы штангенциркуля:
Vernier calipers, to be used, to measure, external and internal sizes, a part, to consist of, steel scale, four jaws, two jaws, to be attached, the frame, to slide, the scale, the first two jaws, to be used, measuring external surfaces, the other two jaws, measuring internal surfaces, the depth, to be measured, a spindle.
9. О твечая на вопросы, объясните принцип действия микрометра:
1. What is a micrometer? 2. What is the function of the graduated thimble of the micrometer? 3. What is the scale on the micrometer barrel used for? 4. Where is the part placed for measurement? 5. How is the part pressed to the anvil and how is the micrometer reading taken?
Date: 2015-12-13; view: 695; Нарушение авторских прав